The first thing that you should know when building circuits for electrical devices are the theories in basic electronics. Get to know the various components used in them and how to properly connect them to each other. And study how to make and read schematic diagrams that represents graphically the electrical circuit using images and symbols.
It is important to do so when you want to make a certain device but are confused still with some parts concerning the process. Voltage divider is an example of an advanced topic which the produced output is only a portion of what its input is. But first, learn or review the theories on basic electronics and understand the advance stuffs better.
Start by identifying the two kinds of electricity that are direct current and alternating current which are also known as DC and AC respectively. In AC, the direction where the electrical signal flows is alternating or reversing constantly with Hertz used to measure the reversal rate. In DC though, the movement is one directional from power source, commonly batteries, into the ground.
A closed circuit is when the electric current is allowed to pass through a path from power source to ground which normally indicates a device is functioning. While an open one breaks this path and will prevent the movement just like in turning off a machine. This is done with a switch so you could alternate between them instead of removing the source.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together can be done in two ways which are called series and parallel with the former indicating that all components are wired after the other. While the latter indicates that the parts are wired next to each other and which makes electricity pass them simultaneously. Both ways could be used in building your own circuits.
Adding resistance into circuits is done with resistors and they reduce current flow and are also available in a variety of values measured with ohms. They have wattage ratings also and their value is indicated by colored bands around their body. You could learn reading these bands or look up for graphs that helps in calculating their values.
Capacitors are components that stores electricity then discharges them when it drops and is measured in Farads with common ones being microfarad, nanofarad and picofarad. The commonly used types of capacitors are ceramic disc and electrolytic. The former being non polarized and the latter polarized requiring one of its leg to be properly connected with the power or ground.
Diodes are polarized components allowing current to pass through one direction and would cause a voltage drop. One of its side is called cathode which connects to power and the other is anode. These are just samples of the basic theories you must learn in making electrical devices.
It is important to do so when you want to make a certain device but are confused still with some parts concerning the process. Voltage divider is an example of an advanced topic which the produced output is only a portion of what its input is. But first, learn or review the theories on basic electronics and understand the advance stuffs better.
Start by identifying the two kinds of electricity that are direct current and alternating current which are also known as DC and AC respectively. In AC, the direction where the electrical signal flows is alternating or reversing constantly with Hertz used to measure the reversal rate. In DC though, the movement is one directional from power source, commonly batteries, into the ground.
A closed circuit is when the electric current is allowed to pass through a path from power source to ground which normally indicates a device is functioning. While an open one breaks this path and will prevent the movement just like in turning off a machine. This is done with a switch so you could alternate between them instead of removing the source.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together can be done in two ways which are called series and parallel with the former indicating that all components are wired after the other. While the latter indicates that the parts are wired next to each other and which makes electricity pass them simultaneously. Both ways could be used in building your own circuits.
Adding resistance into circuits is done with resistors and they reduce current flow and are also available in a variety of values measured with ohms. They have wattage ratings also and their value is indicated by colored bands around their body. You could learn reading these bands or look up for graphs that helps in calculating their values.
Capacitors are components that stores electricity then discharges them when it drops and is measured in Farads with common ones being microfarad, nanofarad and picofarad. The commonly used types of capacitors are ceramic disc and electrolytic. The former being non polarized and the latter polarized requiring one of its leg to be properly connected with the power or ground.
Diodes are polarized components allowing current to pass through one direction and would cause a voltage drop. One of its side is called cathode which connects to power and the other is anode. These are just samples of the basic theories you must learn in making electrical devices.
About the Author:
You can get great tips for picking a voltage divider supplier and more information about a reliable supplier at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
No comments:
Post a Comment